In the previous post we have seen how to determine the efficiency of DC machines using the method

**Swinburn's test**. Now there is an another method to determine the efficiency of a DC machines called as Regenerative method or Hopkinson’s Test method. This method saves the power and gives much accurate result of a DC machine. To carry out this test, we need similar DC machines and supply voltage.### Working Principle:

Two similar DC Shunt machines are coupled mechanically and parallel connected across DC source. Both the machines; one is running as a motor and another is running as a generator by varying the shunt field excitation. The electrical power given to the motor is converted to mechanical power, the rest going to the different motor losses. This converted mechanical power given to the generator. The electrical power generated from the generator is given back to the motor except the power wasted as generator loss. Thus the electric power is taken from the DC supply is the sum of motor losses and generator losses and this can directly read through ammeter and voltmeter. Since the input power from the DC supply is equivalent to the power needed to provide the losses of two machines, this test can be done only with a small amount of power. By varying the machine field strength, we can put any load on the machine. Therefore the total loss of the machine we can determine at any load. The machines commutation performance and the temperature rise can be observed since the machine tested at full load condition.

The figure above shows that typical circuit diagram of a Hopkinson’s test. Two similar DC shunt machines are coupled mechanically and parallel connected across the DC source. By varying the each machine field strength 1

^{st}machine M is allowed to run as a motor and other machine G run as a generator. The motor draws current I_{1}from the generator and current I_{2}from the DC source. Thus the current input to the motor is (I_{1}+I_{2}). Electrical power taken from the DC source is V_{I}2 and which is equivalent to the total losses (motor losses and Generator losses). The shunt field current of motor is I_{4}and the Generator is I_{3}.

__Calculation:__
Let V = Supply voltage

Motor power Input = V(I

_{1}+ I_{2})
Generator power Input = VI

_{1}_{}
We can determine the efficiency of DC machines in two cases.

**Case 1:**

*Assuming that the efficiency of both the machines are same.*

**Case 2:**

*Assuming both the machines has same iron loss, friction loss and windage loss.*

__Case 1:__####
**Assuming that the efficiency of both the machines are same. **

Motor output power = η x Motor Input power

= η V(I

_{1}+I_{2})
I.e. Motor Input power = Generator Input

Now the Generator output = η x generator Input

= η x ηV(I

_{1}+I_{2})
= η2 V(I

_{1}+I_{2})
VI

_{1}= η^{2}V(I_{1}+I_{2})
∵ Generator output η =

**√**{I_{1}/ (I_{1}+I_{2})**The above expression is used to determine the efficiency satisfactorily perfect for a rough test. If case need to find more accuracy then the efficiency of the two machines can be determined separately using the below expressions.**

__Note:__

__Case 2:__**Assuming both the machines has same iron loss, friction loss and windage loss.**

It is not necessary to assume that the efficiency of both the machines are same. It is due to that both the DC machines don’t have the same armature winding and the field winding. However the iron loss, friction loss and windage loss of both the machines will be same due to both the machines are identical. On this notion we can find the efficiency of each machine.

Let,

R

_{a}= Armature winding resistance of individual machines.
I

_{3}= Shunt field current Generator G
I

_{4}= Shunt fief current of Motor M
Generator armature copper loss = (I

_{1}+I_{3}^{2}) R_{a}
Motor armature copper loss = (I

_{1}+ I_{2}– I_{4}^{2}) R_{a}
Shunt field copper loss in G = VI

_{3}
Shunt field copper loss in M = VI

_{4}_{}

Power drawn from the DC source is VI

_{2}and is equal to the total losses of motor and generator.
VI

_{2}= Motor and Generator total losses
To get the iron loss, friction and windage loss subtract the armature copper loss and shunt copper loss of both the machine from VI

_{2}.
Total losses of 2 machines (M & G)

= VI

_{2}– [(I_{1}+I_{3})^{2}R_{a}+ (I_{1}+I_{2}-I_{4}^{2}R_{a}+VI_{3}+VI_{4})] = W
To find the individual machine losses divide by 2

i.e. Total losses of each machine = W/2

####
**To find the efficiency of Motor **

Input motor power = V(I

_{1}+ I_{2})
Total Losses = (I

_{1}+I_{2}-I_{4}^{2})R_{a}+ VI_{4}+ (W/2)
= W

_{m}_{}

Efficiency of Motor η

_{m}= (Input – Losses) / Input
=

**[V(I**_{1}+I_{2}) – W_{m}] / [V(I_{1}+I_{2})]#### To find the efficiency of Generator

Generator output power = VI

_{1}
Total Losses = (W/2) + (I

_{1}+I_{3}^{2})R_{a}+ VI_{3}_{}= W

_{g}

_{}

Efficiency of Generator

**η**_{g}= VI_{1}/ (VI_{1}+W_{g})
Focus on your own ad duplicate and focus on the best keywords. Lastly, enhance the website landing page experience.

ReplyDeleteinteractive design company

They develop this site on your own plus it seems greater than incredible search engine optimization support.

ReplyDeleteproduct design firms San Francisco

For example, if you are writing a multiple choice quiz, write 3-5 possible answers, making one of those the correct answer. dumb b test

ReplyDeleteI am confident you've got a great enthusiast following there.

ReplyDeleteSilicon Valley web design